If you are considering the idea of connecting gutter downspouts, this is the guide for you. After reading this, you will learn how to do this with ease. Indeed, it can be a tricky task if you don’t know what you’re doing.

You want to make sure that the project is done safely and correctly. If successful, the water will be diverted away from your home. If you feel like you’re stuck somewhere following this guide, you can always contact a professional for any additional assistance.

With that said, let’s begin with the following steps below.

Gather the necessary tools

The first thing on how to connect gutter downspouts, you’re going to need tools. You want to gather the necessary tools and gutter downspout parts such as connectors, elbows, straps, and hangers. Once you gather these, you can begin by cutting the downspout at a 45-degree angle to ensure that it fits properly into the elbow connector.

Then, you will need to attach the elbow connector to the bottom end of the gutter. Secure it with pop rivets or screws. You can continue to attach additional elbows and connectors as needed.

Do this until you reach ground level. After this, secure each connection with hangers or straps. When installing downspouts for rain gutters, you’re doing the right thing by helping your gutter system work properly during days of heavy precipitation.

Measure and cut piping

Before you begin to connect the gutter downspouts, make sure you are making the right measurements. You should also cut the piping that will be used. Use a tape measure and a saw that can cut metal for this stage.

You’ll want to measure the length of the pipe that is needed to run from the gutters to the outlet location. After you’ve measured the pipe, mark it with a permanent market and begin cutting with a saw of your choice. Then, you’ll want to fit any elbows or other pieces needed for the bends in the drainpipe.

Like the metal pipe, you’re going to measure each elbow piece and market it. Then, you will cut each elbow piece with the saw you’re using. Make sure that the edges are not jagged as it can cause problems with your drainpipe system.

Connect the downspout elbows

Now, it’s time to connect the downspout elbows. This doesn’t have to be difficult. So long as you have the right tools and some patience, you’ll be able to secure the connections in no time.

To begin, you will need to take one of your elbows and insert it onto the end of the pipe. Be sure that you have inserted it firmly. Keep it in place with the help of a clamp or a fastener.

To ensure a tight fit, use a wrench or pliers. After securing both pieces, take the second elbow and repeat the same thing that you did. Then, you want to make sure that all the connections are tight before moving on.

You want the downspouts to become secure. That way, they won’t come loose on days when the weather gets bad. Trouble can even occur even after heavy rainfalls.

The more secure the connections are, the better.

Install downspouts

Now, here comes the fun part. At this stage, you’ll need to start measuring the gutters to ensure that they are the right length with the downspout. Mark where the downspout will be connected to the gutter and drill holes for each end. Attach one end of the downspout to the gutters with rivets or screws.

Then, slide the other end in place and secure it with rivets or screws as well. For curved sections of the gutter, you may need special elbows to help fit around the corners. Be sure to measure carefully before making the necessary cuts.

After all the pieces are in place, secure them. You may need to use a sealant for extra security and watertightness. Install splash blocks or underground drains at the bottom of each downspout so it can carry any excess water away from your foundation walls and prevent pooling.

You can have an underground drainage installed if the soil conditions are good enough. This may not be the case if the conditions are poor among other factors. In this case, you will need splash blocks that can direct runoff away from your home.

Attach Downspout Extensions

Finally, it’s time to attach the extensions. You’ll need a piece of steel or aluminum gutter for each downspout along with two pieces of elbow connectors for each gutter section. You will need screws, sealants, and a drill with a screwdriver bit.

Measure the distance from the bottom of the downspout to where you want your gutter to start. This can also help determine the size of your gutter sections and elbows. Cut the gutter sections using tin snips or a power saw.

Each section needs to overlap at least six inches when connected. Attach the elbows to the ends of each section using sealants and screws. Connect the sections to the bottom of your downspouts and check to see if they are secure.

After this, you should be done. Your project is complete. The cost of gutters and downspouts will be worth every penny, especially when you installed them yourself without any professional help.

But remember, you need to make sure that each end is secured properly.

Final Thoughts

If you are considering the idea of installing gutter downspouts yourself, this guide will serve you well. Make sure that you follow every step in order to make sure you get the job done properly. When this is complete, you’ll need to make sure that it will do its job properly.

You can pour a bit of water down the gutter to see if it will drain well. If it does, then you should be good to go. Your gutter and downspout will be able to handle all kinds of weather.

Also, be sure to install gutter protection systems to ensure that your gutter stays as effective as possible.

Contact Storm Master Gutters for all your gutter needs!